2013 Dodge Ram 1500 5.7 Hemi Serpentine Belt Diagram - Truck Guider (2024)

The 2013 Dodge Ram 1500 5.7 Hemi Serpentine Belt Diagram can be found in the vehicles owner’s manual. The diagram shows the proper routing for the serpentine belt on the 5.7 Hemi engine. This is a V8 engine that produces 383 horsepower and 400 lb-ft of torque.

It has a maximum towing capacity of 10,450 pounds and a payload capacity of 1,720 pounds. The 2013 Ram 1500 is available in four different trim levels: Tradesman, SLT, Sport, and Laramie.

If you’re like most people, you don’t think about your car’s serpentine belt until it breaks. Then, you’re scrambling to find a replacement and figure out how to install it. To save yourself the hassle, it’s a good idea to familiarize yourself with your car’s serpentine belt diagram.

The serpentine belt is a crucial part of your car’s engine, and it is responsible for powering many of the engine’s accessories. If the belt breaks, those accessories will no longer work. In some cases, the engine may even overheat without the serpentine belt.

To avoid being stranded on the side of the road with a broken Serpentine Belt, take a few minutes to learn about your car’s Serpentine Belt Diagram. This simple drawing can help you understand how the Serpentine Belt works, and it can also help you troubleshoot problems should the need arise.

2013 Dodge Ram 1500 5.7 Hemi Serpentine Belt Diagram - Truck Guider (1)

Credit: www.amazon.com

How Do You Put a Serpentine Belt on a 5.7 Hemi?

If your 5.7 Hemi engine needs a new serpentine belt, you’ll be glad to know that it’s a relatively easy process. Here’s a step-by-step guide to putting on a new serpentine belt on your 5.7 Hemi engine:1) First, open the hood and locate the tensioner pulley.

This is the pulley that keeps the proper tension on the serpentine belt.2) Using a wrench or ratchet, loosen the bolt on the tensioner pulley so that you can move it out of the way.3) Take off the old serpentine belt by simply slipping it off of all of the pulleys except for the tensioner pulley.

4) Put the new serpentine belt around all of the pulleys EXCEPT for the tensioner pulley, and then feed it around that last pulley as well. You may need to wiggle things around a bit to get everything lined up properly.5) Once everything is in place, use your wrench or ratchet to tighten up the tensioner bolt again so that there is proper tension onthe new serpentine belt.

Make sure not to overtighten! And that’s it!

How Do You Change a Serpentine Belt on a 2015 Dodge Ram 1500?

Assuming you have the proper tools, it is a relatively simple process.First, locate the tensioner pulley. This is usually found near the front of the engine.

On some models, you may need to remove a plastic cover in order to access it. Once located, use a wrench or socket to rotate the tensioner clockwise. This will loosen the belt so that you can remove it from the pulleys.

Next, thread the new belt around all of the pulleys except for the tensioner. Be sure to route it according to the diagram on your vehicle’s fan shroud or in your owner’s manual – if unsure, consult a professional mechanic. Once everything is lined up, use your wrench or socket to rotate the tensioner counter-clockwise until tight.

You may need to hold it in place while you start the engine in order to get enough slack out of the belt to finish tightening it properly.And that’s it! Just remember: when working with any parts near or attached to your engine, always take extra caution and be sure to consult with a professional if you are unsure about anything.

What are the Symptoms of a Worn Out Serpentine Belt?

If your car is equipped with a serpentine belt, it’s important to know the signs of a belt that needs to be replaced. Here are four symptoms of a worn out serpentine belt:1. Squealing Noises

One of the most common signs that your serpentine belt needs to be replaced is squealing noises coming from the engine bay. The squealing noise is caused by the belts’ ribs beginning to wear down and no longer making proper contact with the pulleys. If you hear this type of noise, it’s important to have your vehicle inspected as soon as possible so that you can avoid more serious engine damage down the road.

2. Cracks and FrayingAnother symptom of a worn-out serpentine belt is cracks or fraying on the surface of the belt. Over time, exposure to heat, oil and other elements can cause the belt material to break down and crack.

Once cracks start to form, it’s only a matter of time before the belt completely fails and snaps. Inspect yourbelt regularly for any signs of cracking or fraying and replace it if necessary.3. Engine Overheating

One of the most serious consequences of a worn-out serpentine belt is engine overheating . The Serpentine Belt drives several components in your engine including the water pump . If the water pump isn’t working properly , it can cause coolant to stop circulating throughout your engine which will lead to overheating .

Another component driven by the Serpentine Belt is t he power steering pump . If this stops working , you may notice increased resistance when turningthe steering wheel . This can eventually leadto complete loss offunctionalityand may even cause damage to other parts inyour system .

In short , don’t ignore any warning signs that yourSerpentined Beltmay be failing – Replacingit sooner rather thanlater could saveyou alotof moneyand hasslein th long run !

Where is the Routing on a Serpentine Belt?

If you’re looking for the routing on a serpentine belt, it’s actually quite simple. The routing is usually stamped onto the back of the belt. However, if it’s not there, you can easily find it online or in a repair manual.

5.7 Hemi Belt Routing and Removal

2014 Dodge Ram 1500 5.7 Belt Diagram

The serpentine belt on the 5.7L engine in the 2014 Dodge Ram 1500 is located at the front of the engine and drives all of the accessories. The belt routing diagram is located on the underside of the hood. To change the serpentine belt, first loosen all of the accessory pulleys so that there is slack in the belt.

Then, remove the old belt and route the new one around all of the pulleys except for the tensioner pulley. Use a wrench to rotate the tensioner pulley clockwise until there is enough slack to slip onthe new belt. Oncethe newbeltis in place, start upthe engine and checkfor proper operationofallacces-soriesbeforedrivingaway.

2012 Dodge Ram 1500 5.7 Belt Diagram

If you’re looking for a 2012 Dodge Ram 1500 5.7 belt diagram, you’ve come to the right place. Here at serpentinebeltdiagrams.com, we have all the information you need to know about serpentine belts and how to properly route them.The 2012 Dodge Ram 1500 5.7 is equipped with a V8 engine that requires two separate serpentine belts.

The primary belt runs from the crankshaft pulley to the power steering pump, water pump, and alternator. The secondary belt runs from the tensioner pulley to the air conditioning compressor and idler pulley.Properly routing your serpentine belts is essential for ensuring peak performance from your engine and preventing costly repairs down the road.

With our easy-to-follow diagrams, you can be sure that your belts are properly routed every time!

2011 Ram 1500 5.7 Belt Diagram

If you’re looking for a 2011 Ram 1500 5.7 belt diagram, you’ve come to the right place. This detailed diagram will show you exactly where to find the belt on your truck, and how to properly route it.

2015 Ram 1500 5.7 Belt Diagram

If you’re looking for a 2015 Ram 1500 5.7 belt diagram, you’ve come to the right place. Here at AutoZone, we have a wide selection of diagrams that can help you find the perfect one for your vehicle.The first thing you need to do is determine which type of belt you need.

There are two main types: serpentine and V- belts. Serpentine belts are more common these days, but if your truck has a V-belt system, that’s what you’ll need to get.Once you know which type of belt you need, it’s time to start shopping around.

Our online catalog has a great selection of belts from top brands like Gates and Dayco. And if you need any help finding the right one for your truck, our friendly and knowledgeable staff is always happy to assist.

Conclusion

In this post, we’ll show you how to change a serpentine belt on a 2013 Dodge Ram 1500 with a 5.7 Hemi engine. We’ll also provide a diagram to help you understand how the belt is routed.

  • 2013 Dodge Ram 1500 5.7 Hemi Serpentine Belt Diagram - Truck Guider (2)

    Zayn

    Zohn Zayn Smith is a seasoned automotive enthusiast with over 15 years of experience in the industry. As the Founder and Chief Editor of Truckguider, he specializes in Dodge Ram models, including the Ram 1500 and Ram 2500. His deep understanding of these trucks makes him a trusted authority on everything from performance and maintenance to towing capabilities.

    View all posts

2013 Dodge Ram 1500 5.7 Hemi Serpentine Belt Diagram - Truck Guider (2024)

References

Top Articles
Latest Posts
Article information

Author: Melvina Ondricka

Last Updated:

Views: 6023

Rating: 4.8 / 5 (48 voted)

Reviews: 95% of readers found this page helpful

Author information

Name: Melvina Ondricka

Birthday: 2000-12-23

Address: Suite 382 139 Shaniqua Locks, Paulaborough, UT 90498

Phone: +636383657021

Job: Dynamic Government Specialist

Hobby: Kite flying, Watching movies, Knitting, Model building, Reading, Wood carving, Paintball

Introduction: My name is Melvina Ondricka, I am a helpful, fancy, friendly, innocent, outstanding, courageous, thoughtful person who loves writing and wants to share my knowledge and understanding with you.